Read and debounce multiple buttons using interrupt on AVR microcontrollers

This library provides an easy way for reading and debouncing one or multiple buttons connected to a microcontroller. Apart from basic functionality, the library provides some extra functions such as reading a combination of buttons, and detecting a button long press or a double pressed button. These are especially useful in a low button count system.

Multiple buttons can also be read by a single ADC pin.

Contents

• What is button debouncing
• Button debouncing in software
• Usage example
• API
• Millis timing library
• Setup
• Setting long press timeout
• Check reading complete
• Get pressed buttons
• Get active buttons
• Check for long pressed buttons
• Check for double pressed button
• Read a button combination
• Download

 

What is button debouncing

millis and micros library for AVR microcontrollers - milliseconds and microseconds time tracking

Having precise timing in microcontrollers is important in many projects. For this you can use the two libraries presented in this article - millis & micros.

millis library triggers a timer interrupt every 1 millisecond and increments the milliseconds variable. The user can select the size of the milliseconds variable ranging from char (8 bits) to long long (64 bits) with an overflow from 255 milliseconds to 584.9 million years.

micros library is almost the same as millis but for microseconds. The overflow is between 255 microseconds and 584942 years.

For both libraries the user can select which timer to use: Timer0, Timer1, Timer2, Timer3 or Timer4.

In the case of millis library, it is recommended that other interrupts take less than 1 millisecond to complete otherwise the millis timer interrupt will be delayed. For the micros the ISRs must finish in less than 100 microseconds. The faster the CPU clock the better.

For the milliseconds and microseconds variable decide if you really need a 32 or 64 variable (long and long long) because the bigger the variable the longer it takes to increment it. For example on a 1MHz CPU it takes about 77 microseconds to increment a long long variable.

 

ISP programming rig for microcontrollers

I had to program many types of microcontrollers over the years and so I was thinking why not build a simple programming rig to make things easier. This rig is for the In-system programming (ISP) method and not for the UART method.

The board in the above image is not the programming rig but a digital clock shown as an example. Notice the 6 pin header near the cap. The pins are not soldered through hole but on SMD pads. This way it can be easily de-soldered after finishing the project and on some space constrained projects this is a must.

Constant current LED driver using ATtiny13 - Headlamp flashlight

Here is a simple constant current source for driving 7 white 5mm LEDs and also 2 red LEDs. I have made the circuit for a headlamp flashlight that had a soft button which required a microcontroller. To save the battery life the microcontroller is powering down when the lights are off with a current draw of only 0.3uA.

Capacitive transformerless power supply schematic for PIR motion sensor NV-1111.35

In the previous article I have explained how a PIR motion sensor works. There you can also find the schematic for the NV-1111.35 PIR sensor which is based on a popular three stage op-amp topology. Understanding this can help you understand other pyroelectric sensors as well.

This sensor is powered by a capacitive transformerless power supply with an output of 8V and 7mA of current.

How an outdoor motion PIR sensor switch works with schematic

In this article I will be explaining how a pyroelectric (PIR) sensor works and show the reverse engineered schematic simulated in LTspice. The schematic is for NV-1111.35 outdoor PIR sensor used to switch a mains light and has 3 potentiometers for setting SENSITIVITY, LUX and TIMEOUT.

This sensor is based on a popular three stage op-amp topology. Understanding this can help you understand other pyroelectric sensors as well and also something about active filters using LM324 and removing and setting a DC voltage bias.

 

Using USBTinyISP programmer with Atmel Studio 7 | AVR programming

In the last article I talked about Programming any AVR microcontrollers using WinAVR and USBTinyISP but recently I found that USBTinyISP can be easily used together with Microchip Studio.

For microcontrollers that are using UPDI interface for programming, I have another tutorial here.

Using an external programmer in Microchip Studio 7